Key points for the production and management of capsules

Key points for the production and management of capsules

Key points for the production and management of capsules one

Pretreatment of raw materials

(1) before the use of raw materials, the name, specification, quantity, number and qualification certificate should be checked.

(2) the processed raw materials are loaded into clean and dry containers, and labels are attached inside and outside.

Key points for the production and management of capsules two

Burdening and granulating

(1) check the labels of the powder and thick paste (the extract) that are transferred before the process.

(2) when the ingredients are calculated and fed, the operator and the reviewer are required to sign the production records.

(3) a variety of granulated pouch is needed. When granulating, the mixture must be mixed evenly and gradually added a certain proportion of thick paste or adhesive. When a batch number is granulated several times, the particle size should be uniform and the consistency is uniform.

(4) for the technical conditions such as temperature, concentration and quantity of granule mixture, the necessary technical parameters must be made according to the characteristics of varieties, and the operation must be strictly controlled. Pure water should be used when granulating water.

(5) weighing instruments should be calibrated before use and calibrated regularly.

Key points for the production and management of capsules three

Dry

(1) to control the thickness and quantity of wet particles in dry disc according to the regulations of the varieties. The drying process should be often turned over and regularly ventilated to record the drying temperature regularly in order to prevent the coking and control the moisture of the particles within the specified range.

(2) the uniformity of the oven temperature should be checked regularly.

(3) when the fluidized bed is used for drying, the air used should be cleaned and dedusting. During operation, the phenomenon of material sticking should be checked continuously to make it dry evenly.

Key points for the production and management of capsules four

Whole grain

(1) permanent magnet should be installed in the hopper of the pellet machine to remove the iron dust from accident.

(2) aromatic materials are added in the whole process according to the prescribed content, so as to mix evenly. After mixing the aromatic particles into the container, they should be stored in containers for more than four hours to facilitate uniform penetration.

(3) the mixed particles are packed in a clean container. Inside and outside the container, labels should be attached, indicating the name, batch number, lot size, number, date, and work number, and sent to the intermediate station in time.

(4) special toxic species should be produced in closed rooms, and operators should be isolated. Dust suction devices should be installed indoors, and dust excluded should be disposed centrally.

Key points for the production and management of capsules five

Bursa

(1) check the name, specification, batch number and quantity of the hollow capsule semi-finished products before packing.

(2) hollow capsules, semi-finished products and finished products should be placed in a constant temperature and humidity chamber. The room temperature should be controlled at 18~28 degrees centigrade and the relative humidity is 45% to 65%.

(3) manual packing: each board dose should be fixed, weighing, rechecking and signing; set up a special person to test the quality difference, each board inspection after inspection and acceptance, the sub board should be fixed management. Both receiving and sending are required to verify the quality and issue problems. They should be repaired or exchanged in time.

(4) machine division: should be set up to be responsible for the debugging and maintenance of equipment, pre loading test loading, and check the volume difference, appearance, the test installed after the test can be opened, the machine should be regular sampling inspection of the average loading, timely adjustment of the machine, test unqualified capsules should be reworking department.

(5) weighing instruments used for weighing and testing should be corrected before use and checked regularly.

(6) the semi finished products are packed into clean and dry containers, sealed and preserved to prevent moisture absorption. Labels should be attached inside and outside the container, indicating name, batch number, specification, quantity, number, date, and number, and then transferred to the next procedure or intermediate station.

Key points for the production and management of capsules six

Examination of the capsule and light

Before removing the capsule, the outer wall of the capsule must be cleaned and rejected. Wipe the outer wall of the capsule and then polish it according to the technological requirements. The capsule that is qualified for appearance inspection is put into a clean and dry container. After attaching the label inside and outside, the capsule is transferred to the intermediate station.

Key points for the production and management of capsules seven

Packing

(1) pretreatment of packaging materials. First, glass bottles are scrubbed with drinking water, and then rinsed with pure water for high temperature sterilization and dry cleaning. The storage time should not exceed three days. Second, the plastic bottle cap should be packed and the outer packing of the bottle stopper should be tight and clean and dry. 3. The inner package of cotton and paper that is directly exposed to drugs should be cleaned and sterilized properly, dried and kept after sterilization.

(2) when the aluminum plastic packaging is used, the temperature of the heat seal should be strictly controlled. The handwriting printed on the thin aluminum should be carefully removed or blurred.

(3) the number of utensils should be checked, cleaned, kept and distributed.

(4) the name, specification and batch number of the packaging label must be checked and proofread. After the packaging is finished, the number of labels, the number of useful and the remaining number should be accurately counted. Residual label and scrap label management methods.

Guangdong richpacking specializing in the production of automatic capsule filling machine, semi-automatic capsule filling machine, in the industry has a good reputation and service, there are needs of the capsule filling machine friends please contact us.