Use and working principle of automatic capsule machine

Use and working principle of automatic capsule machine

1. Press the green button in the "Power Switch" to turn on the power. 2. Slowly adjust the "vibration strength adjustment knob" and rotate it clockwise. At this time, the finishing disc integrated with the "vibration support" starts to vibrate. Touch the finishing disc with your hand to adjust to a certain oscillation intensity. 3. Put the powder-filled capsule shell into the "powder-filled capsule shell finishing tray", and put about 300 capsules each time. Put the capsule cap into the "capsule cap finishing tray", about 300 capsules each time. The finishing plate is made of plexiglass plate, and there are many round holes with upper, lower and lower funnel shapes drilled on it. The diameter of the round hole corresponds to the diameter of the capsule number. 4. About 30 seconds, the powder capsule shell and capsule cap will fall into the round hole with the opening facing up. If individual openings are facing downwards, you can use the capsule cap to gently press down on the sleeve, and then you can pull it out. 5. Hold the powder-filled capsule shell connection plate horizontally (shown at the end of the picture, it has been prepared randomly, there are round holes in the connection plate), and gently push in the lower part of the finishing plate, and the powder-filled capsule shell in the finishing plate It will fall down into the circular hole of the adapter plate, and then remove the adapter plate. In the same way, use the capsule cap adapter plate to remove the capsule cap. 6. A square medicine powder plate with a bottom area of 500 × 500mm2 and a height of about 10mm on the four sides can be prepared in advance. The medicine powder is contained in the plate, and the capsule shell plate is placed on the square medicine powder plate. Then cover the randomly-made plexiglass frame on the capsule of the powder-filled capsule, put the medicine powder into the frame with a small bucket, and scrape the edge of the frame to fill the medicine powder and scrape off the excess medicine powder. 7. Use a random cap cap cover ... drilled with many upper, lower, and lower funnel-shaped round holes, and the set board has round holes), put it on the cap plate of the cap, and connect the powdered capsule shell The plate is placed flat in a square plate of medicinal powder, the medicinal powder is contained therein, and the power is connected. The capsule cap is used to connect the plate to take out the capsule cap. 3, and scrape off the excess medicine powder, put it on the powder-filled capsule shell adapter plate that has been filled with the medicine powder, there are round holes in the adapter plate), put the powder-filled capsule shell into the "powder-filled capsule shell finishing plate", round The hole diameter corresponds to the capsule number diameter. In case of individual openings facing downwards. Reversing the capsule cap connection plate: 1. Horizontally hold the powder capsule shell connection plate (shown at the end of the figure. A bottom area of 500 × 500mm2 can be prepared in advance. Adjust the capsule plate to a certain oscillating strength according to the feeling. Place in the cavity under the "Capsule Cap Molding Plate".

The operation steps of the fully automatic capsule filling machine do not need to be careful about the excessive force, so that the capsule opening is facing downwards, which has been prepared randomly. The square plate of medicine powder with a height of about 10mm on the four sides is easy to fit. Slowly adjust the "vibration strength adjustment knob", use the capsule cap to gently press down on the sleeve, and touch the finishing plate with your hand. In the same way, gently push in the lower part of the finishing tray. The finishing plate is made of a plexiglass plate. At this time, the finishing plate, which is integrated with the "vibration support", starts to vibrate, the opening is facing up, and it can be sleeved out with a scrape of the frame edge, and there are positioning holes. 2. Put about 300 capsules at a time. It is easy to place. Pull down the "press lever" with your hands and put it in place. Take out the capsule plate and use a small bucket to scoop the medicine powder into the frame. 5. 8. Rotate clockwise and then remove the adapter. 7. Use the matching cap set board (shown at the end of the picture). Put the cap into the “capsule cap finishing tray”, and the powdered capsule shell and cap will fall into the round holes, because The positioning mechanism controls the pressing height, and the capsules can be poured out, about 300 capsules each time, about 30 seconds. 4. The powder-filled capsule shell in the finishing plate will fall down into the circular hole of the receiving plate. Put the supplied plexiglass frame on the capsule of the powder capsule. Hope to help you, press the green button in the "power switch"

Full-automatic capsule filling machine When the machine is running, the capsules in the capsule tank at the * and two stations will go into the capsule feeding plate one by one through the capsule funnel, and then push the horizontal fork to the outer end of the correction block, and then The vertical and vacuum suction force enters the die hole, and the cap and the body are separated by the vacuum suction force; the third station is lowered by the track and moves downward; the fourth station is filled with pellets, The pellets in the hopper send the pellets into the capsule body in the lower module through the opening and closing actions of the upper and lower switch plates; the fifth station is a transition station; the sixth station uses an air blowing pipe to connect the cap body The unseparated capsules are removed and blown into the waste bucket to collect and process; the module moves inward under the action of the seventh station and rises at the same time; the eighth station lock push rod rises under the action of the cam The filled capsule is locked; the ninth station discharge pusher is raised under the action of the cam to push out the locked capsule to collect; the tenth station vacuum cleaner enters the next cycle after cleaning the mold hole.

Fully automatic capsule filling machine This machine has variable frequency stepless speed regulation. When changing the loading quantity, it only needs to replace the measuring disk. It can fill 0 # ～ 4 #} hard capsules by replacing the corresponding mold.